5 Pin Relay Connection

April 21, 2024 Post a Comment

5 pin relay connection

5 pin relays provide 2 pins (85 & 86) to control the coil and 3 pins (30, 87 & 87A) which switch power between two circuits. They have both normally open and normally closed connection pins. When the coil is activated, power will be switched from the normally closed pin to the normally open pin.

What would you use a 5 pin relay for?

And what we typically use them for is we are connecting them to a power source. So instead of using

Do all 5 pin relays work the same?

The problem is, not all relays are the same. Many relays, if installed for the wrong application, could and will cause a short (Internal Relay Circuit) and most likely cause functionality issues or even damage to the vehicle computer systems.

Which pin is ground on a 5 pin relay?

Pin 85 connects to the ground. Pin 87A - When the switch is turned off, power is drawn from this pin. It is not required to be used and can be completely ignored if not required.

What is 85 and 86 on a relay?

85 and 86 are the coil pins while 30, 87, and 87a are the switch pins. 87 and 87a are the two contacts to which 30 will connect. If the coil is not activated, 30 will always be connected to 87a. You can think of this as the switch in OFF.

How do you tell which pin is which on a relay?

Every relay has a coin the white one which when energized activates the contacts. So of all the pins

Why use a relay instead of a switch?

Relays can reduce the need for high-amperage wiring and switches, which are expensive and take up space. Therefore, switching to relays in your electronic systems can reduce the size or weight of a casing, for instance, or allow manufacturers to fit more functionality into a space of the same size.

What are the 5 different types of relay?

What are the Types of Electrical Relays

Electromagnetic relay. Electromagnetic relay is the simplest, oldest and most widely used relay.
Latching relay. ...
Thermal relay. ...
Reed relay. ...
High voltage relay. ...
Time Relay. ...
Current and voltage relay. ...
Differential relay.

How do you test a 5 pins relay?

Testing the Normally Closed Terminals Place one of the lead probes on the COM terminal and the other on the normally closed terminal. Then read the resistance on the screen. If it reads resistance of close to zero ohms, then the relay is working well and should not be changed.

Does it matter which way you wire a relay?

Touch the 86 wire to the battery's positive post, and the 85 wire to the battery's negative post. Actually, unless the relay has a diode in it, it won't matter if the polarity is switched; the electromagnet will be energized regardless.

Can I use 5V on 12v relay?

Yes. With the above figure you can surely run a 5v relay on 12v.

Does a relay need to be grounded?

Generally, anything metal is required to be grounded… the base of a solid state relay is metal … so if the SSR is mounted inside metal enclosure, the enclosure must be grounded or covered for protection against dangerous voltages.

Which pin is ground on a relay?

Realizing that 85 and 86 are the coil pins, these pins will be transferring the current through the coil. 85 will be used to ground your relay, while 86 will be connected to the switchable power. 87 and 87a will be connected to your controlled accessories that you wish to turn on and off with your relay.

Is ground pin positive or negative?

And in electronics, ground is just a name we give to a certain point in the circuit. For example, in a circuit with one battery (with a positive and a negative terminal), we usually refer to the negative terminal as ground.

Which is ground on relay?

The second pin, or ground is the housing which must be mounted direct to chassis or otherwise grounded. If your relay is in a plastic housing it will have 2 pins for the coil, usually reversible. Your toggle switch is breaking the 12v power line between one side of coil and power.

What do pins 30 and 87 do on a relay?

Terminal 30 is connected to the battery. So when the electromagnet pulls the two internal switch contacts together, current flows from terminal 30 out terminal 87, which is connected to the device we want the relay to control, in our case an electric motor. Since the motor is grounded, this causes the motor to turn on.